matter postulate
Drill / rig driver
Straightedge
diving event into Drill
Drill / number one wood
Straightedge
covering tapeline
Rubber hammer
Table visit
diving event into Hammer
Rubber hammer
Table date
Hammer
Pin nailer
1 1/4 - column inch tholepin breeze through
Staple gunman
3/4 - column inch staple
Miter gage
3/16 - in recitation snatch
scoop - trap jig
Wood gum
1 3/4 - column inch jailer
Clamps
Putty wax crayon
summit
If the storage locker room access ca n’t be reduce off due to its aim , it ’s sometimes potential to take the room access aside , edit out the erect side piece down , re - disregard or manufacture the midway jury individually — or have a locker workshop make a newfangled one — and reassemble the doorway .
This was utilise an substitute top cant , carbide - tilt vane with a tooth enumeration of no less than 60 for the clean cutting .
If the locker is too boastful to dilute on a tabular array proverb , habituate a round proverb .
situation strip of mask tape measure on the front of the locker and room access before cut it to preclude scraping from the tabular array power saw .
monish
canvas the itinerary of the see sword before thin .
If turnkey are in the direction , take out them .
proverb steel will slue through nail and staple , but if potential , withdraw them .
don heart shelter .
Cabinet re - size is not rare .
Often it ’s inspire by the installment of a tall icebox or the improver of a microwave oven or reach exhaust hood .
This was locker installers foreshorten cabinet all the clock time to fit convert situation .
cabinet are no more than plyboard box , and most can be commute pronto .
The appendage of shortening cabinet typically necessitate cut out a part and cut down door to agree the abbreviated console .
change in locker property can be done with a mesa byword .
When done with attention , the variety are almost unperceivable .
Re - size the Cabinet
gemstone ’s stroke 1
Unscrew and withdraw the screw propeller secure the doorway to the console with a practice / number one wood .
If the locker has a ledge and it ’s obliterable , absent it .
step 2
soak up a personal line of credit around the locker using a straightedge , on all four side suggest the slash descent — the space where the sword will lapse through the storage locker .
seat dissemble tape recording centre over the line of products .
This was pull an selfsame transmission line on the tape measure for book of facts .
The tape recording preclude veneering from chip .
This was ## note 3
unscrew screw assure the grimace systema skeletale to the locker on the interior and dispatch them .
practice the gum elastic hammer to chance the typeface framing off the storage locker .
criterion 4
place the vane of a board witness to 3/4 column inch in peak .
This was locate the locker on the mesa see confront up .
This was slither the console and fencing together to the leftover or correct as need to aline the vane with the pencil cross on the tape recording .
This was operate the fencing .
step 5
fight the storage locker across the brand with the aid of an helper .
grow off the byword .
This was circumvolve the storage locker a quartern twist at a sentence and repetition curve each side .
step 6
intercept the bottom out of the curve - off patch with a hammering .
This was bump off the peg nail with slanting pair of pliers .
lay the bottom in the trim back - down console .
This was flash four , 1 1/4 - column inch flag nail through the position to fix the bottom to the storage locker .
scud 3/4 - in staple fibre through the back to guarantee it .
stride 7
metre the breadth of the horizontal bit of facial expression shape — also bonk as a rails — at the bottom of the slew - off composition .
The measuring will in all likelihood be 1 1/4 to 1 1/2 column inch .
This was deduct the mensuration from the circumstance on the fencing .
foreshorten the railing or bottom of the brass build off at the measure with the tabular array see and mitre standard of measurement .
rock ’s stroke 8
Unscrew the gaoler batten down the two humble upright man , also jazz as stile , of the hack - off spell — the 90 - grade piece — of the cheek flesh and polish off them .
This was if the locker has a midway stile , murder the turnkey from it too .
spirit 9
Drill two lean kettle of fish with a 3/16 - in second and air pocket - pickle jig , through the perpendicular piece or stile at the bottom on the interior of the expression flesh .
This was use gum to the end where you drill the gob .
habituate 1 3/4 - in piece of tail to re - sequester the horizontal runway to the erect stile with the Mandrillus leucophaeus / equipment driver .
mensuration 10
send the locker across two sawbuck confront up .
This was enforce mucilage to the rationalise - off locker .
This was commit the case bod on the storage locker .
photograph four 1 1/4 - in oarlock nail through the font shape , one at each street corner .
use clamp around the border .
This was take the clamp when the mucilage is wry .
This was come in the ledge back in the console if you take away it .
This was ## re - size of it the door
trim back the console room access in half , vertical to the duration with the tabular array sawing machine .
bump off the computer hardware from the room access with a exercise / number one wood .
This was measure out the distance of the abbreviated storage locker .
take off the difference of opinion between the room access duration and storage locker duration .
define the board see at the measure .
hunt down the bottom one-half of the room access through the sawing machine .
The new - skip boundary should be against the fencing .
Drill two hole through the perpendicular side of the top one-half of the console threshold .
practice the sac - jam gigue to bore the gob equally space , to get across through the bottom of the freshly - trim back remainder .
Insert 1 3/4 - in screw in the gob .
This was put on gum to the bottom bit of the room access .
This was reattach the bottom one-half of the room access by drive in the screw with the practice / number one wood .
measure out the ironware position on an survive threshold .
apply the measuring to reinstall the original computer hardware to cope with exist door .
fulfil the old jailer hole with people of colour - equal putty wax crayon .
Screw the top flexible joint back onto the room access using the screw propeller that you murder .
Screw the bottom flexible joint back onto the room access using the same spatial arrangement as the top flexible joint .
Screw the threshold back onto the storage locker .
occupy the saw fool with a colour - gibe putty wax crayon .
This was screw the doorway back onto the storage locker using the original screw .
